Direct answer
Build a load list from appliance power, hours and starting demand. Review usable battery energy, losses, inverter limits and charging before selecting a system.
Size a home backup battery from the appliances that must remain powered, the time each will operate and the power they need when running together. Then check that energy estimate against usable battery energy, system losses, inverter limits, charging opportunities and installation conditions. A battery’s kWh label alone cannot establish whether it is suitable for the home.
A well-prepared load list makes the first system review more useful. It also lets the buyer decide which loads are essential and which can remain off during an outage.
Build the list around an actual backup period
Choose a specific scenario, such as keeping selected lights, a router, a fan and a laptop available during an evening interruption. For each device, record its quantity, running power and required hours of operation. Use measured consumption where practical; a label or charger rating may not represent the device’s average use.
Keep starting demand in a separate column for appliances with motors or compressors. A refrigerator, pump or air conditioner cannot be evaluated from an energy total alone. State which appliances are likely to start or operate at the same time.
Work out load-side energy
For an assumed constant load, energy in kWh is watts multiplied by operating hours, divided by 1000. The U.S. Energy Information Administration explains why watts and watt-hours describe different quantities.
The table below is an illustration of the method. Its device powers and operating times are assumed values, not measured customer data, typical consumption claims or a completed system design.
| Assumed load | Combined running power | Operating time | Load-side energy |
|---|---|---|---|
| Four 10 W lights | 40 W | 5 hours | 200 Wh |
| One router | 15 W | 8 hours | 120 Wh |
| One fan | 45 W | 6 hours | 270 Wh |
| One laptop load | 60 W | 3 hours | 180 Wh |
| Total for the assumed period | 160 W if all run together | Different hours by load | 770 Wh, or 0.77 kWh |
The 0.77 kWh total is energy required at the loads. It is not yet the required battery nameplate capacity. It also does not describe motor starting demand, since no motor-starting profile is included in this example.
Translate the estimate into a battery requirement
For a preliminary calculation, divide the load-side energy by the usable fraction of the battery’s listed energy and by the assumed delivery efficiency. Define the usable fraction after the intended reserve has been allowed for, so the reserve is not counted twice.
If the example assumes a usable fraction of 80% and delivery efficiency of 90%, the calculation is 0.77 ÷ 0.80 ÷ 0.90 = about 1.07 kWh of listed battery energy. Those percentages are illustrative assumptions only; they are not specifications for any KEZHUN model.
The final review must replace the assumptions with configuration-specific information and account for relevant operating conditions, system consumption and the required performance over time. Starting state of charge also matters: a battery that is not sufficiently charged at the beginning of an outage cannot supply the same energy as a fully prepared system.
Check inverter power as a separate requirement
Add the running power of the appliances expected to operate together, then assess their starting requirements. Compare both with the proposed inverter and battery system’s documented limits. Increasing battery energy does not automatically increase the inverter’s output capability.
If a requirement includes an air conditioner, water pump or another cycling appliance, provide its exact model and operating information. A single nameplate value should not be converted into a precise backup-duration promise without checking how the appliance actually runs.
Include charging and installation conditions
Describe how and when the system can recharge. If solar is part of the arrangement, include the existing or proposed module and inverter information, site conditions and the expected charging window. Do not assume the battery will recover fully between outages merely because solar charging is available.
Also record the required AC voltage and frequency, the intended installation location and any existing equipment that must be retained. These inputs help distinguish an integrated residential energy storage system from a separate battery and inverter arrangement.
If you are considering an integrated wall-mounted system, use our wall-mounted energy storage buying checklist to review the model, included components, electrical configuration, installation information and documents before requesting a quotation.
What to send for a useful first review
- Destination and required electrical configuration.
- Appliance quantities, running consumption and known starting requirements.
- Hours of operation during the intended backup period.
- Which loads run together, and which can be switched off.
- Existing solar, battery or inverter model information.
- Available charging periods, installation conditions and intended order quantity.
Have a load list ready? Send it to KEZHUN for a system and quotation review. The list supports a configuration-specific discussion; it is not a substitute for the installation design.
Preparing a commercial ESS project? Send the site, loads and delivery requirements for review: Submit a commercial project brief